Introduction
- Joined 7 months ago
- 2 Achievements
- 162 Points
Pinned Items
Recent Activities
-
admin commented on this post about 4 months agoFinished tacking the flanges to the web for the 2 side rails. decided not to trim flanges to the correct width until I have attached the sides together braced them and fully welded them together.
Also, Tyres arrived during the week $15 bucks each + $12.50 shipping each. Not off roaders but they'll do for a start.100000Comments (3)-
Mick$27.50 a corner is an absolute bargain. Paid three times that for mine at the local M/C shop.5 months agoReported
-
MiddoYeah a good bargain, but I found the auction with the same photos on ebay where the seller had bid for them at Graysonline and paid $40 for IYeah a good bargain, but I found the auction with the same photos on ebay where the seller had bid for them at Graysonline and paid $40 for I estimate 60 tyres. Now that's a bargain. More ...5 months agoReported
-
adminIs this the one? https://www.ebay.com.au/itm/275854518581 Looks like postage has increased, but still a good deal.4 months agoReported
Post is under moderationStream item published successfully. Item will now be visible on your stream. -
-
Hi Tim
Tim here also, I am in Victoria but I'm a bit far away - Mildura.
When I get this kart built I might have to do a bit of travelling to meet with other Cycle Karters. Might be finished around March April next year.
Hope you have...Hi TimMore
Tim here also, I am in Victoria but I'm a bit far away - Mildura.
When I get this kart built I might have to do a bit of travelling to meet with other Cycle Karters. Might be finished around March April next year.
Hope you have success in finding some localsPost is under moderationStream item published successfully. Item will now be visible on your stream. -
Post is under moderationStream item published successfully. Item will now be visible on your stream.
-
Mick commented on this post about 6 months agoContinuing work on the Chassis Side Rails, the mid chassis sections in the photos will be completed during the week. Once the top and bottom flanges are tacked into place the flanges will be trimmed to follow the contour of the outside web with the overall width of each rail being 35mm. Next week I plan to start work on the forward section of...Continuing work on the Chassis Side Rails, the mid chassis sections in the photos will be completed during the week. Once the top and bottom flanges are tacked into place the flanges will be trimmed to follow the contour of the outside web with the overall width of each rail being 35mm. Next week I plan to start work on the forward section of the chassis that support the front springs. I am resisting doing any substantial welding until the whole frame is tacked together.MorePost is under moderationStream item published successfully. Item will now be visible on your stream.
-
Mick reacted to this post about 6 months agoBit of a one step forward and two steps back day. tacked a flange to the chassis rail web today but went a bit heavy with the tacks and bowed the web in the direction it shouldn't.
I dealt with it like any good Cyclekart builder should, I kicked a tin of bolts in anger and then sat in front of the TV with a beer and pondered my life choices....Bit of a one step forward and two steps back day. tacked a flange to the chassis rail web today but went a bit heavy with the tacks and bowed the web in the direction it shouldn't.More
I dealt with it like any good Cyclekart builder should, I kicked a tin of bolts in anger and then sat in front of the TV with a beer and pondered my life choices. Scrap that one and start again.
Next time I will lightly tack both flanges and not do any welding until I have both left and right rails in a temporary jig and control the heat.Post is under moderationStream item published successfully. Item will now be visible on your stream. -
Stream item published successfully. Item will now be visible on your stream.
-
Post is under moderationStream item published successfully. Item will now be visible on your stream.
-
Mick commented on this post about 6 months agoHi all, new Cyclekart builder here. Have finished designing my Alpha Romeo P2 in AutCad including the curved chasis and making the MDF buck to construct it on. Will post some photos soon.100000Comments (1)
-
Awesome stuff. I'm also planning to make a buck to metal form the boat tail on mine but still a long way off from that. Very interested to see yourAwesome stuff. I'm also planning to make a buck to metal form the boat tail on mine but still a long way off from that. Very interested to see your build. More ...Reported
Post is under moderationStream item published successfully. Item will now be visible on your stream. -
-
Post is under moderationStream item published successfully. Item will now be visible on your stream.
-
Post is under moderationStream item published successfully. Item will now be visible on your stream.
There are no activities here yet
You need to login to read the rest of the stream items.
Unable to load tooltip content.